Liangshan silicone mold release agent manufacturers price Zibo

News: Liangshan silicone mold release agent manufacturers price Zibo News








Marble is a high-end decorative material, so you must be careful when choosing it to avoid wasting money. The slightly experienced stone practitioners know that as a natural material, stone is affected by geophysical and chemical changes, coupled with the influence of many factors such as mining and processing, and the quality of the same product is quite different compared to other traditional industries. In terms of products, on-site evaluation is very important. The quality of the appearance of marble can be identified from the following items. The marble with good uniformity and quality has uniform texture and fine texture; while the marble with coarse grain and unequal grain structure has poor appearance and poor quality. Dripping ink is a simple test method to test the quality of the stone.


Fluorocarbon paint treatment mainly uses fluorocarbon supporting system to coat concrete, generally including putty, epoxy sealing primer, epoxy intermediate paint, fluorocarbon topcoat. After spraying the paint, the original color of the concrete will be covered and the appearance It is the color of fluorocarbon paint, which can protect for a long time, prevent corrosive media from immersing, and protect concrete. The main interface agent currently is silane impregnant, which is a colorless and transparent liquid that can maintain the original color of concrete. Good permeability, excellent water resistance, resistance to chloride ions, and prevent the penetration of corrosive media. The silane impregnant is mainly sprayed and applied twice. Compared with fluorocarbon paint spraying, it is easier and faster.


Silicone release agent
Product description:
The release force is strong, the mold does not accumulate, and the surface of the product is smooth. Compared with other water-based release agents, silicone release agents have better safety and product appearance.


Appearance
Milky white milky liquid

Ingredients
Water-soluble silicone emulsion

Solid content
30%

Specific gravity
1.0



News: Liangshan silicone mold release agent manufacturers price Zibo News








In developed countries, indoor radioactivity testing has long been routine. It is understood that the United States needs to conduct indoor radioactive contamination testing when the new home is delivered to use. In order to prevent radioactive contamination of the living room, it is recommended that you check whether the radioactivity of the stone materials used, such as walls, floor tiles and slag cement exceed the standard before decoration, and whether the radon and formaldehyde concentration exceeds the standard in the room after the decoration. If any problems are found, they should be dealt with in time. To achieve this, your room decoration project not only improves the quality of life, but also guarantees health, making your home decoration project a green decoration project without radioactive pollution. When testing, you must ask a special testing organization that holds the "CMA Analysis Test Book" issued by the State Technical Supervision Bureau and the "Environmental Impact Assessment Grade A Certificate" issued by the state. They can use advanced testing equipment to come to your home for you Radioactive contamination of decorative materials and indoor harmful gases-radon and formaldehyde concentration detection, and based on the test results, provide you with a CMA analysis test report certified by the National Bureau of Technical Supervision.


The coating pellet protective layer is a new type of building material, and the material cost is almost the same. The roof coating pellet protective layer is flexible and waterproof, saving labor and less pollution. Compared with two felts and three oils, adding mung bean sand to waterproof, less pollution, and it is much better than rigid waterproofing. Thermoplastics are generally polymerized from petroleum-based monomers. The polymerized product is generally powder. The powder is not convenient for storage and transportation, and it is not convenient for processing and molding. Generally, it is pelletized by an extruder to prepare pellets. In the granulation process, additives such as antioxidants are generally added to increase the storage time of the raw materials and give other functions to the material. Extended information: Granulation method Water ring cutting: The head of the granulator cuts materials under water, and the surface of the prepared pellets is smooth and round. Generally, large petrochemical plants use this cutting method. Stretching and pelletizing: The plastic melt is pulled out from the pelletizer head, cooled by a water tank, and then crushed by a pelletizer. The pellets prepared are generally cylindrical. Generally, modification companies or small R&D institutions use this type of pelletizer. Granule method. Reference source:-Pellets


How to use:


1. 1. Before use, it is generally diluted with 3-10 times tap water, and the specific dilution ratio needs to be determined according to the complexity of the product and the actual situation.


2. Except for water, please do not add any other additives to the concentrate.


3. On the pre-treated or cleaned mold, spray the release agent 3-5 times under normal processing temperature to ensure that the mold has a uniform release mold formation.


4. 4. Each spray can be demoulded 5-10 times.


Store:
After use, please cover the barrel tightly and keep the barrel in a cool place.





News: Liangshan silicone mold release agent manufacturers price Zibo News








The slightly experienced stone practitioners know that as a natural material, stone is affected by geophysical and chemical changes, coupled with the influence of many factors such as mining and processing, and the quality of the same product is quite different. It is relatively different from other traditional materials. For industry products, on-site evaluation is very important. The quality of the appearance of marble can be identified from the following items. To determine the pattern color tone, under the condition of sufficient light, place the selected slab and the same batch of other marble slabs on the ground at the same time, standing at a distance of 1.5m from them and carefully visually inspecting them. It is required that the pattern tones of the same batch of marble slabs should be basically harmonized. Check the surface defects. Under the condition of sufficient light, place the plate flat on the ground, stand at a distance from the marble slab lm and observe the invisible defects as no defects; stand at the distance from the plate lm but not obvious at 1.5m There are no obvious defects; the obvious defects at a distance of 1.5m from the plate shall be considered defective.


The composition analysis of the expansion agent is not very troublesome. You only need to take your product samples and go to the Ingeer testing agency, and they will give you an analysis report that satisfies you.