Wuhai foaming agent serves the people

Wuhai foaming agent serves the people

Can chemical raw material recycling factories accept a small amount? We recycle a wide variety of resins. We recycle resins no matter how large or small, we recycle resin products, we come to our door, and we collect high-priced cash from all over the place.

Bokai Chemical Trade Recycling Company specializes in the recycling of chemical products that are fully recycled, such as chemical raw materials, dyes, pigments, paints, rubber, waxes, chemical additives, chemical metals, etc.

Our company serves every customer attentively and guarantees the quality of every acquisition process. Caring for the environment is the responsibility of each of us. The waste of resources is a shameful behavior. Promoting the recycling of chemical raw materials and dyes is an important mission of our company.





We will continue to uphold the tenet of "one time cooperation and mutual trust, many times cooperation and mutual benefit", and look forward to cooperating with you! High-priced door-to-door recycling, unlimited quantity, you are welcome to visit at any time, call for consultation, and create and develop together. We seek common development with customers.

Recycling dyes manufacturer Bokai Chemical Trade Recycling Company said that acid dyes are widely used in fabric dyeing and people often use them, but the color fastness of these dyes is usually very poor. Recycled dye manufacturers say that some users repair dyes that meet the standards. However, we need to pay attention to certain things that need to be paid attention to when fixing dyes. Let us take a look!

Wuhai foaming agent serves the people






2. Check if the paint is contaminated, replace it immediately. 3. Inventory and eliminate the pollution sources within the paint line, such as butter, wax or contaminated hands, containers, clothing and rags.
4. The compressed air is filtered and the compressor drains water regularly. 5. The coating line should be fully ventilated and exhausted to reduce the possibility of air pollution. 6. Check the paint quality and refuse to use expired or deteriorated paint. 7. When fish eyes occur, stop the line immediately, clean the site and add no more than 3% leveling agent to the coating. 8. Products with fish eyes should be sanded before rework. (5) Orangepeel 1. Symptoms-The surface of the Symptom coating film shows wrinkles similar to orange peels.

Applicable technical guide: applied to dye nylon fibers with acid dyes, and then process the dyed products. After dyeing nylon fibers with acid dyes, the dyed product can be treated with NBS to improve its wet fastness, especially to water, sea water, washing, and sweat. The fastness can be significantly improved. Similar to all such additives, The degree of improvement in fastness varies depending on the dyeing method and fiber.

To

Concentration of acid dye: 1.0-2.0% (owf) NBS (calculated based on cloth weight) After dyeing nylon fiber with TELONL, SUPRANOL or other selected acid dyes, wash it with soft water, and then dye the dyed product with NBS at PH4.5, 70-80℃, 20-30 minutes, post-treatment.

To

Note: If you increase the amount of NBS by one third, you can also use hot air to complete the fixation operation. The wet fastness has been improved to a considerable extent, but the temperature should not exceed 180-185℃. If the temperature exceeds, or the saturated steam is treated, it will affect the NBS. When dissolving or diluting NBS, it is necessary to prevent direct contact with concentrated acetic acid. The contact of NBS with concentrated acetic acid will cause precipitation. Any precipitation that has occurred can be easily dissolved by adding a small amount of ammonia.

To

If there are non-ionic additives in the post-treatment, it will cause precipitation and impair the NBS effect (before fixing, it can be washed with a soaping agent to prevent abnormalities). If the dyed product is coated with PU or film in the later process, do not fix it with NBS, otherwise it will affect its adhesion effect. The nylon batting that uses NBS as a post-treatment feels very rough, which will affect its subsequent weaving operations. Therefore, for this kind of dyeing, only dyes with higher wet fastness should be selected for dyeing, without fixing treatment.

Wuhai foaming agent serves the people






3. Check whether the paint has expired or deteriorated.
4. Check if the thinner is used incorrectly or has deteriorated. 5. When using two-component paint, be sure to follow the standard operation. 6. When spraying multiple times, the drying time between coatings should be sufficient. 7. The viscosity of the paint is at an appropriate level. 8. Before drying at high temperature, be sure to let the solvent in the paint have sufficient time to evaporate. 9. The temperature difference between the inside and outside of the drying room should not be too large. 4. The volatilization speed of the thinner is too fast. 5. When spraying repeatedly, if the bottom layer is not fully dried, spray continuously. 6. The pressure of compressed air is too high. 7. The compressed air contains moisture. 8. The moisture content of wood is too high. three.

To sum up, the content mentioned above is the related matters shared by the recycled fuel manufacturers. Bokai Chemical Trade Recycling Company supports door-to-door chemical raw material recycling, dye recycling, paint raw material recycling, high-priced recycling and other businesses. If you have any needs in this regard, please call for consultation!