Elastomer modified Lexue root puncture-resistant waterproofing membrane for waterproofing of bridges, roads, parking lots, swimming pools, tunnels, reservoirs and other buildings. It is especially suitable for the protection and protection of pipes and anti-corrosion coatings in areas with frequent structural deformation and cold areas. In order to maximize the construction quality of waterproofing membranes, special attention must be paid to the storage and transportation of waterproofing membranes, and the waterproofing membranes should be stored and transported in accordance with regulations. When the user saves the roof waterproof membrane, it should be stored separately, and avoid storing in places that are susceptible to water, or contaminated by organic solvents, oils and other materials.
Polyester tire, 50 kg, 1*10 meters, low temperature resistance -5 degrees, 140/roll, 50 pieces. 4mm, polyester tire, 50 kg, 1*10 meters, low temperature resistance -10 degrees, 180/roll, customized. 4mm, polyester tire, 50 kg, 1*10 meters, national standard -20 degrees, 280/roll, customized national standard. 4mm, polyester tire, 50 kg, 1*10 meters, national standard -25 degrees, 350/roll, customized national standard. Customization cycle: 23 days. Waterproof membrane construction: SBS type construction is 6 yuan per square meter, including liquefied gas, and polypropylene construction is 5 yuan per square meter. During the 4mm construction, there will be overlap between the coil and the coil. After construction, each coil will be 85% square. For example, a roll of 10 square SBS will be squared in actual construction.
Waterproof membrane zKqE6QEF9
The installation of elastomer-modified Lexue root puncture-resistant waterproof coiled water-stop steel plate includes the upper steel frame and the lower steel frame, which are installed at the place where the concrete is placed before and after the concrete is poured. The lower steel frame and the network respectively pass through the gap between the upper and lower steel frames of the waterstop in the horizontal direction. The waterstop is connected to the steel plate fixing group positioned along the vertical direction. As mentioned, the positioning of the upper reinforcement is to connect the upper floor. Reinforced and fixed, multiple supports are welded to one end of the steel frame reinforcement steel bars, the other end is welded to the bottom steel bars, and the upper steel frame is connected to the spacer steel bars.
Elastic line, trial laying: pop up the control line on the base coating according to the actual overlap area, and strictly follow the control line to test and actually glue the coil to ensure that the coil overlap width is 6~7cm (there is on the coil Logo). According to the characteristics of the site, determine the elastic line density to ensure that the coil is pasted smoothly and will not be skewed due to accumulated errors. The coil should be placed in place for a trial first, and then the actual gluing can be started after the correct shape is cut according to the needs. Node processing.
The construction technology of waterproof coiled material mechanical fixing method. Mechanical fixing is to use special fixing parts, such as metal gaskets, screws, metal battens, etc., to mechanically fix the coiled material and other roof-level materials on the roof base or structural layer. Mechanical fixation includes point fixation and linear fixation. The bearing capacity and arrangement of the fixed parts are strictly designed according to the experimental results and relevant regulations. Sundries and debris on the surface of the base layer. Laying a vapor barrier (polyethylene film). In the past, asphalt felt has been used as the main waterproof material for roof waterproofing. However, natural wind, frost, rain and snow, solar radiation, temperature changes and other external unfavorable factors will affect the normal use of ordinary waterproof membranes, especially the influence of sunshine, temperature, and rainfall. Of course, there are also some internal factors. For example, the structure of the roof itself, improper construction methods, and later use have caused the leakage or damage of ordinary roof waterproofing membranes. The above is the reason for the leakage of self-adhesive waterproofing membrane compiled for you by the editor of Shandong Yuexu Building Materials. I hope it will be helpful to you.
Waterproof membrane can be used as roof waterproof layer, but also can be used as underground waterproof layer. When used as a roof waterproof layer, it mainly prevents rain and snow from intermittently infiltrating the roof. When used as an underground waterproof layer, it mainly prevents groundwater from constantly infiltrating the building, whether it is used as a roof waterproof layer or as an underground waterproof layer. Layers must be leak-free, which involves the design of the waterproof layer, the quality of raw materials, construction operations and maintenance management. Among them, the construction operation is the main link to ensure the quality of the waterproof layer.
The influence of the roof usage process. During normal use, the asphalt linoleum waterproofing membrane is damaged due to roof repair or other equipment installed on the roof. When the Master’s roof is overhauled, the asphalt felt can easily be stepped on without paying attention to protection. When other equipment is installed on the roof, ordinary waterproofing membranes may be damaged for fixing. The roof is an external maintenance structure covering the upper layer of a building. Its main function is to protect human production and life from natural dangers. Some tips can be used when selecting on-site. Appearance label inspection: look at the model, manufacturer, address, certificate, production license number, implementation standard, negative temperature label, etc. Appearance identification. A. Check for cracks with a length of 10mm or more on the entire roll. B. For ordinary coils, unfold the coils as a whole at a high temperature of 30 degrees in summer to see if they are stuck. c. See if the tire base is completely saturated: No matter what type of roll material, as long as there is a tire base, whether the tire base is saturated or not is related to the waterproof performance and durability of the entire roll material. The method is very simple, use a knife to cut the small A piece of coiled material, look at its middle part. Secondly, it depends on the quality. If it is completely black, the penetration is good. If there are white or gray stripes and spots, the tire base is not fully penetrated and the coil is not qualified.
.
Click image to view original image
